1
ENGLISH 02N-095000
Congratulations on purchasing your TIMEX
®
watch. Please read these
instructions carefully to understand how to operate your Timex timepiece.
Your watch may not have all of the features described in this booklet.
For more information, please visit: Timex.com
HOW TO START YOUR WATCH
To start your watch, remove the plastic guard from under the crown
(if applies), set the Time and Date (if applies), then press the crown in
against the case (position A). Slowly turn the crown clock-wise until you feel
resistance. You should hear the watch “ticking” and the second hand will
begin to move. As you wear the watch the movement of your wrist will wind
the movement automatically. If the watch is worn daily the movement will
retain enough energy to prevent the watch from stopping. If the watch stops
due to non-wear, follow the instructions to set the Time and Date (if applies),
and wind to start the watch again.
WATER AND SHOCK RESISTANCE
If your watch is water-resistant, meter marking or (O) is indicated
Water-Resistance Depth p.s.i.a. * Water Pressure Below Surface
30m/98ft 60
50m/164ft 86
100m/328ft 160
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY
BUTTONS UNDER WATER.
1. Watch is water-resistant only as long as crystal, crown and case remain
intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
4. Shock-resistance will be indicated on the watch face or caseback.
Watches are designed to pass ISO test for shock-resistance. However,
care should be taken to avoid damaging the crystal.
TO SET TIME
1. PULL crown to position C and turn until the hour and minute hands
display the correct time. Note correct time of day (A.M. or P.M.) for proper
date function (if applies). The date will advance between 9:00 PM and
1:00 AM
2. Push crown to position A.
TO SET DATE (IF APPLIES)
1. PULL crown to position B and turn COUNTER-CLOCKWISE until correct
day appears. Note: if the date is set between the hours of around 9:00 PM
and 1:00 AM, the date may not change the following day. If this occurs,
reset the Time and Date at any other time than between the hours of
around 9:00 PM and 1:00 AM to ensure proper date function.
2. Push crown to position A.
CB
A
HOW TO ADJUST BRACELET
(Variations of the following bracelet sections apply to all watch models).
SLIDING CLASP BRACELET
1 Open locking plate.
2. Move clasp to desired bracelet length.
3. Exert pressure while holding locking plate and slide clasp back and forth
until it engages in grooves on underside of bracelet.
4. Press locking plate down until it snaps closed. Clasp can be damaged if
excessive force is used.
FOLDOVER CLASP BRACELET
1. Find spring bar that connects bracelet to clasp.
2. Using a pointed tool, push in spring bar and gently twist bracelet to
disengage.
3. Determine wrist size, then insert spring bar in correct bottom hole.
4. Push down on spring bar, align with top hole and release to lock in place.
Fig. 2Fig. 1
Fig. 3
BRACELET LINK REMOVAL
REMOVING LINKS:
1. Place bracelet upright and insert pointed tool in opening of link.
2. Push pin forcefully in direction of arrow until link is detached (pins are
designed to be difficult to remove).
3. Repeat until desired number of links are removed.
RE-ASSEMBLY:
1. Rejoin bracelet parts.
2. Push pin back into link in opposite direction of arrow.
3. Press pin down securely into bracelet until it is flush.
CROWN POSITION
DATE
この商品に関する会話に参加する
ここでは、Timex TW2T69900ZV Waterbury 時計 についての意見を共有できます。 疑問がある場合は、まず説明書をよく読んでください。 マニュアルのご請求は、お問い合わせフォームより承ります。